The Builders Hardware Manufacturers Association (BHMA®) has announced the publication of revisions to five product standards, all of which have been approved by the American National Standards Institute (ANSI). Doing so, the association says, reinforces its commitment to public safety.

“BHMA reviews each ANSI/BHMA standard at least once every five years to ensure that our standards continue to meet the ever-changing needs of both the public and our industry,” said BHMA Standards Director Michael Tierney. “This work is essential for maintaining alignment with modern quality requirements in our industry.”

Revisions to all standards included edits, renumbering and updates to references but five sections went a little deeper.

The four changes to ANSI/BHMA A156.1: Butts and Hinges were:

• Added concealed hinge requirements, along with accompanying type numbers and drawings;
• Added zinc to the type numbers and gave it the numeral 9;
• Reorganized Tables 3.8 and 4.6; and
• Removed finish requirements (now consolidated in A156.18).

ANSI/BHMA A156.6: Architectural Door Trim had the most changes:

• Added new product types environmental test criteria to scope;
• Removed finish requirements (now consolidated in A156.18);
• Reorganized definitions into common types/ families and added new definitions;
• Modified 3.2 to add tolerance for temperature;
• Modified stainless requirement in 3.4;
• Modified material requirements from minimum material thickness to nominal thickness, added throughout;
• Added language to 4.3.3 to allow larger diameter and longer length screws;
• Modified polishing language in 4.3.4, 5.3.3 and 6.3.4 and relocated in the appendix A-2;
• Added new language to 4.3.4 for fasteners for latch protection plates and vertical rod covers;
• Bevel Edge language in 4.3.5 relocated to appendix A-2;
• Added new section to 4.4 for performance tests for adhesive mounted door protection plates;
• Added new types and illustrations to Figure 1 (door protection plates);
• Added new types to Figure 2 (door and wall edging);
• Added additional symbol and options to 6.3.7 and 7.3.10;
• Updated 7.5 with new test and added criteria for push/pulls;
• Added new type to Figure 4 (door pulls); and
• Updated Figure 6 and added a new Figure 7.

To ANSI/BHMA A156.20: Strap & Tee Hinges, the changes are:

• Removed finish requirements from section 7 (now consolidated in A156.18);
• Added new language to 1.2 to reference finish requirements in A156.18;
• Added language to 4.1 and 5.2 to clarify measurement equipment and measurement method; and
• Cleaned up and added new Figure 1 illustration.

The changes to ANSI/BHMA A156.22: Door Gasketing and Edge Seal Systems are:

• Removed acoustic properties from scope;
• Updated verbiage in 3.3: to change “listed” to “certified;”
• Moved Tolerances and Measuring Criteria from 4.7 to 4.1 to align with other standards layouts;
• Updated illustration in 4.6;
• Added verbiage to 4.7 to clarify set up of adhesion test fixture and updated illustration;
• Added language to 5.2 and 7.1.3 to clarify 20 minute anodize;
• Modified acoustic performance in 5.5 and moved to appendix A-5;
• Combined 10.9 with language in 10.2 to align information on retainer material;
• Combined 10.10 with language in 10.3 to clarify when to use the “Y” designation;
• Updated numbering system examples in 10.7 and 10.8 and added titles;
• Updated verbiage in appendix a-6; and
• Retitled appendix charts 1 and 2 to clarify intent that they are reference guides.
And for ANSI/BHMA A156.26: Continuous Hinges, the changes are:
• Removed finish requirements from 3.3 and 6.10 (now consolidated in A156.18);
• Added reference to finish standard A156.18 to 1.2;
• Added “also called full mortise” to definition 2.1.3;
• Reorganized tables in section 7;
• Removed A115 reference from appendix; and
• Updated Figure 1 with new illustration.

Each ANSI/BHMA standard can be purchased on the BHMA website, and summaries of each standard can be accessed on the Hardware Highlights page.

Leave a Reply

Your email address will not be published. Required fields are marked *